Home Assistant tutorial on Ubuntu Core

Install Home Assistant and create a motion-activated light automation with this tutorial

Overview

In this tutorial, we’ll learn how to install Home Assistant on Ubuntu Core, then create a motion-activated light automation. This is a great starting point for a secure, open-source smart home. By the end, we’ll have learned the skills we need to create Home Assistant automations of our own with whatever smart home devices we wish.

Materials required:

• Raspberry Pi 4
• Power cable
• Case (recommended)
• SD card (at least 8GB recommended)
• SD card reader (if not built into your computer)
• Aeotec Z-Stick Gen 5+ Z-Wave USB stick
• Aeotec MultiSensor 6
• Aeotec LED Bulb 6 Multi-white
• A monitor with an HDMI interface
• A mini-HDMI cable
• A USB keyboard
• A USB power adapter

Installing Ubuntu Core

Duration: 20 minutes

We’ll start by following the instructions here to install Ubuntu Core on our raspberry pi, making note of its IP address during the process.

Pairing the Z-Wave devices

Duration: 3 minutes

We can pair the bulb and multi-sensor to the Z-Wave stick without installing any software. The Z-Wave stick has a battery in it, so it doesn’t even need to be plugged in!

First, we’ll install the bulb in a light fixture, switched off. After pressing the button on the Z-Wave stick, we should see blue light flashing around the button. Now, we’ll switch on the bulb that will flash a few times to indicate it is searching for a Z-Wave host with which to pair. The two should automatically detect each other and pair.

Now, we’ll plug in the USB power cable included with the multi-sensor into the sensor and our USB power adapter. We’ll press the button on the Z-Wave stick again and confirm that we see the flashing blue light. There is a “tamper button” on a corner of the rear panel of the multi-sensor. We’ll press the tamper button, and the multi-sensor should pair with the Z-Wave stick automatically.

Installing the Home Assistant snap

Duration: 4 minutes

We can connect to the raspberry pi via ssh by opening a terminal on our computer and running the command:

ssh @

Now, we’ll run the command:

snap install home-assistant-snap

This will install the latest version of the Home Assistant snap from the stable channel

To support the Z-Wave stick, we will need to install a Z-Wave server as well, fortunately, there is a snap for it!

We’ll run the command snap install zwavejs2mqtt, followed by

• snap connect zwavejs2mqtt:raw-usb
• snap connect zwavejs2mqtt:hardware-observe

These commands will give the Z-Wave server access to the USB port so it can talk to the Z-Wave stick. For further information, refer to the documentation here.

Linking Home Assistant and the Z-Wave server

Duration: 3 minutes

We’ll now start the Z-Wave service/daemon by running the command sudo zwavejs2mqtt.enable

Now, in a browser window, we can type in the IP address of the pi, followed by the Z-Wave server port number like this http://:8091

Now, we’ll click on settings and scroll to the Home Assistant section where we’ll enable WS server.

Press SAVE, and we’ll then move to the Z-Wave section of the Settings page. There, we’ll disable the soft reset setting. This is necessary for the particular type of Z-Wave dongle we are using. Ensure as well that the serial port is listed as shown in the screenshot below.

Now, let’s configure Home Assistant. To do this, we’ll open a new browser tab and type the IP address of the Pi and port 8123 like this http://:8123

The UI will prompt us to set our home location, units of choice, and usage metrics preferences. It also may discover some services on your local network to connect.

We’ll skip these for now, and click FINISH.

We should now be able to see the Home Assistant home page. From here, we’ll click Configuration in the left menu, then Devices & Services.

In the Integrations tab, we’ll now click on ADD INTEGRATION.

In the New Integration interface, search for and click on Z-Wave JS, taking care to not use the deprecated Z-Wave integration.

The URL field should be populated automatically, but if not, type in ws://localhost:3000. This comes from the previous setup we did in the Z-Wave server.

We should now see the devices we previously paired to our Z-Wave stick! Set the area fields appropriately. For me, I put Office in the Area field, as I am creating my motion-activated light in my office.

Creating the automation in Home Assistant

Duration: 4 minutes

From the Home Assistant homepage, we’ll now go to Configuration -> Automations & Scenes -> Add Automation. In the pop-up window, choose Select a Blueprint and pick Motion-activated Light from the dropdown.

We need to choose a name for the automation, something like Office Light should suffice. In the Motion Sensor dropdown, we should select our multi-sensor, which should appear automatically.

In the Light section, we’ll select Choose device and select our light bulb from the dropdown.

We’ll now set the wait time to how long the light should remain on with no motion detected, 120 seconds in my case.

Now, we’ll click SAVE and we’re done!

For ideas on what to try next, check out the community forums at Home Assistant, and let us know what you were able to create on Ubuntu Core in our discourse community.